Search results

After updating the “schedule” “days of week” selection is not functional. I had scheduled dosing certain days of the week….

The other option to “sync with current version” is to re-select the control unit or collective from the top left menu. First select menu which will show the choices Status, devices, input, outputs,etc. Now click the down arrow beside the name of your device or collective This will show list of...

I would review setup instructions: HYDROS Control - How to Add a Dual TDS Meter - the input will read once every hour - also you can specify an “offset” if the reading is not the same as your other meter.

I have an iPad mini 2 running iOS 12.5.5 and Hydros App version 2.2.0 (209) firmware 192. The iPad is mounted by the hydros Control units at my tank. Works great!

Try press and release Press and release the “Mode” button to set the ETM pump controller to different positions. WHITE = Same Side ORANGE = Opposite Side CYAN = Back

What Carlos said - confirm your version of the WE is Ecotech …. If it is - I would try to follow the written instructions here: https://www.coralvuehydros.com/product-support/hydros-waveengine/ecotech-marine-vortechs/ Make sure you do step 5 - if they stay blue/red check distance from...

Yes create a schedule and add the pump - https://www.coralvuehydros.com/product-support/hydros-waveengine/add-flow-pump-schedule/

I would follow these instructions - if your pump is new you probably need to downgrade it from Ecotech Möbius … https://www.coralvuehydros.com/product-support/hydros-waveengine/ecotech-marine-vortechs/

Regarding Doser - Does Hydros have a doser released for sale? From instructions: Here is what you’ll need to get started: A Simple Doser Pump Information on the pump’s dosing rate. How many milliliters per minute does the pump run when powered? An open WiFi outlet (Drive Port if using a...

Thanks - Great information for the forum! I did the basic setup using Control 2 and added the TDS using a Control XS port for TDS. Water pressure is high at my house so I don’t need a pump.

Yes 👍

https://www.coralvuehydros.com/product-support/hydros-control/hydros-collective-101/ Look at Figure B in redundant power supplies section. Wave Engine can power the control 4 & xs using (power & data) command bus cables. Terminator goes on one wave Engine bus. Then a data only cable from 1st XS...

Not sure how you identify? I’m sure Coralvue will help you if you provide the model power supply you have! Link to purchase: HYDROS Control Power Supply

Someone can confirm this but From the photos it looks like the control 4 is not connected to the 2 XS units as you have power supply cable and a terminator. For your setup I believe you want all 3 units in your collective correct? If so, I would get the power supplies with a built in terminator...

Check the active in modes selection - make sure your “normal” mode is checked

I would just double check that all devices have been updated to the newest Hydros app version. Also I have found it good practice to kill the app when done using it so when using multiple devices each device loads from the cloud when app is started.

Update -After trying to confirm the pump stopping issue I found if I allow reverse on the XF330 pump output and also the schedule then I do observe the pump stopping as described by others. I normally have mine set to not allow reverse and did not have the pump stopping! Maybe someone else can...

Yes - sorry - after some poking around ETM was not lost in the update - I originally had the ETM as group 2 which did not transfer on updates the ETM pumps to the schedule. Once I increased pump count and selected the ETM choices all is fine. Thanks Carlos

I just updated app and firmware on my collective and WE. I did not add my WE to the collective yet... I have an XF330 using "LPS reef" flow pattern and I am not seeing it stop as described above. However I did lose my EcoTech pairing and wondered if that was expected with the update? I...

I have the 330 and had to invert rotation for it to work correctly. Also check that the pump blades turn freely - mine got bound up once and were sticking and the WaveEngine gave me the pump error in red. Once I fixed the pump all is well!