Search results

Anyone experienced corrosion on usb ports of these HYDROS WiFi Fish Feeder - HYDROS ? Both of mine over saltwater tank are becoming iffy on connection and both port and cord are showing slight corrosion. They are not in splash zone or anything like that, but obvious above a saltwater tank. It...

Any idea why I would be getting pockets of air in dosing tubing? Seems like it's happening across all things Ca, Alk, Mg, Balling Part C, Carbon. Actually carbon was completely drained on both sides down to dosing container. Perhaps it's the way this tubing is attached to the pump heads. I find...

Is there a list somewhere with names for things like this cable? This one in particular is for Octopus pumps and is out of stock currently, seen bus cables out of stock, etc. before as well, so would be good to know what all these connectors are called to maybe source them elsewhere and make...

Never really got to see how Hydros behaves when internet is down, but mine has been for a bit and they seem to randomly reset things or something. Sometimes I hear alarm going off, where it's really only set up for leak detector, or outlets shut down, not sure which, but at least ones...

What am I doing wrong here =) It runs every day at 11am this way or if I change to run every 7 days when day of week selector disappears.

Was something changed recently that made old outlets zombie s3nd notifications? In one salinity probe I removed complaining about low salinity. Removed power outlet complaining about wattage, s3nsor about sensor not connected etc.? Only solution i found is to readd them, remove notification...

Was anyone able to do anything with these to control them from Hydros in some meaningful way?

Is there a way to setup an outlet to turn on based on water level reading wet and to stay on for a period of time after water level becomes dry while depends on mode is off if off? Min run time seems like an obvious solution, but it's not working as expected and just ends up endlessly switching...

So I'm trying to figure out how to setup 4 toggle switches on 0-10v input. I have quad cable, break out connectors for it, and toggle switches with LEDs. Ivve read what I found here on the subject, but still am confused as to how to connect this. Simply connecting to Power+ and Load+ from Ground...

Imagine will need to return this, but can you think of any reason why Port 1 on WE v2 would not be powering up? Can take an output, re-target it to another pump port and move the plug there and all is fine in other 3 ports, but not 1st one.

Just got back up batteries for Krakens and have few questions. ( Battery Amazon.com ) Looks like there are battery readings on Kraken, currently showing Battery Voltage at 13.8V and Current at 1.34A. I'm assuming voltage is what battery reads at the moment and current is what Kraken is pushing...

Just opened up a new Kraken and looks like there are two outputs form Meanwell PS, what is this about? Seems like a bad idea for controller to use one and the other one sitting there without a cap or anything exposed? Also connection to the controller is not very IP67 looking :)

Let's say I have this setup What would be best way to turn on the pump when bottom water sensor is dry and to turn it off when top sensor is wet. And then not to run again until bottom sensor is dry again? Thanks!

Using this or potentially a DIY option - HYDROS Command Bus Cable (DATA Only) - HYDROS how far can things be split apart? I haven't checked for sure, but I would probably want a 100' cable, would this be still good or serial signal would degrade too much? My RO/DI system and an ATO container...

I am thinking about adding Kraken to my future Hydros collective, but it looks like it probably would not be able to quite drive all that I would want. There will be four Radion XR15 G6s (from chart that's 420W already), refugium AI Blade (20W), and Reef Octopus Elite 150-Int skimmer (25W). Of...

I do not have exact example, but have occurred to me several times, where I would override an output to be ON and it would go ahead and do that for some period of time, maybe a minute or so, but then would override itself to OFF and stay there. And yes, outlet would have number of various...

I'm in process of setting up a new reef tank and was wondering how dosers on X10 would rate against something stand alone as I would really only add it to my collective just for the dosers and would still new 2-4 more lol. Looks like replacement wise it would need this to swap the whole head...

Not sure if it's a bug or I'm missing something, but combiner of two outputs that are off ends up in on state. Setting inputs manually to off would trigger combiner to finally go off in OR state. Note all of these outputs are not controlling anything and suspect this is where the bug might be...

Just got new XP8. Trying to set it up through + menu in the app. I can see existing devices in the list even across the house, but new one is not showing up. Anything I can try to do myself before sending it back as DOA? Lights are: Status - Solid Green Mode - Solid Blue WiFi - Pulsing Pink...

https://www.coralvue.com/hydros-waveengine-direct-drive-pump-adapters Is it possible to get pump side connector pictures for these? I'm trying to power new Gyre XF350 with Hydros, but connector I've been used with older one is not quite right. New pump connector has 3 walls separating pins, so...