As I was adding a feeder to my Hydros App. I took the time to rename some outputs and then rearrange the output buttons. When I was done rearranging and went back to the status screen all my output buttons disappeared? When I go the the output page for the collective they all show up. But when I go back to the status page they don't show up? None of the outputs have the invisible switch turned on. How do I get the buttons to show back up on the main status page?
How did you fix this? I'm having the same problem. I didn't rearrange or rename anything. I just have 4 of my 7 feeder outputs missing on the screen, but they are on the output page.
How did you fix this? I'm having the same problem. I didn't rearrange or rename anything. I just have 4 of my 7 feeder outputs missing on the screen, but they are on the output page.
You can set what is displayed on each page in each category. To enter that mode press and hold on one of the tiles for a input output or device and then release. All the tiles should now have a check box. The onse that are checked will show up on that page. Once you have them the way you want them you can exit by the press and hold on one of the tiles. When in that mode you can also rearrange them in the order you want them. If you put the display in a different mode like text or graphs those will have to be setup also. Doing one will not affect the other modes.
I use my iPad most f the time but even then there are too many inputs and outputs for just a single page. I have mine split up into 7 pages. I have each page setup with the inputs and outputs that I want on each page. The pages are on the menu at the top and in this screenshot mine is on the testing page. This page has the inputs and outputs that are used for testing such a pH, ORP, salinity, alkalinity and others. I also have one page that the inputs are set to graph mode so I can just go to that page when I want to see the graphs for my inputs. I do not have a tank in the living room but I do have outputs setup to turn on and off my wife's lighted ornaments with one of the wifi power strips. They are also setup to show specific lights during the different alerts. I have my RODI and mixing station in the garage so there are several controllers out there to control the RODI and mixing station.
I like your setup. Is everything on one collective?
I don't have long enough cables for that, and my husband refuses to drill holes in the floor for me to accomplish what I'd like.
I like your setup. Is everything on one collective?
I don't have long enough cables for that, and my husband refuses to drill holes in the floor for me to accomplish what I'd like.
Yes, it almost all in one collective. I have another collective setup but it only controlling the heaters and measuring salinity and pH in the mixing tank. I do pass signals between the two using relays. I have the data only cable converted to CAT5 since I already had a CAT5 cable from the garage to the room with the tanks. That is from baxk when there was no wifi and all connections to the router were CAT5. They do run through the attic and down the walls. I also have the RODI type 1/4" tubing run through the attic and down the wall but those are in insulated PVC conduit. My ATO and two AWC pumps are also in the garage. The first photo below is my controller board in the garage. It is an older photo back when I still had some Digital Aquatics modules out there. The big white box in the center was already there and is the media center for the house. The cable, phone lines come into that box and then go to the different rooms. The Router and cable modem used to also be in that box at one time. The second photo is the mix tank, fresh salt water reservoir and DI reservoir. There are there button boxes at each of the reservoirs. The one at the mix tank turns on the work bench light when pressed. It will stay on for 30 minutes and then go off unless I press it again to turn it off. The other one in that box is the mix ready button. After I add the salt mix to the mix tank and it is ready for use I press that button to let the Hydros know. The second one at the mix tank is one for dispensing salt water from the fresh saltwater reservoir into containers or buckets. The second one is a switch that disables the AWC and the other push buttons when it is turned on. The third box only has one button in use and it is to dispense DI water into containers for use. I use that one most since I always need DI water for test, mixing the All For Reef and mixing the KH buffer. Each of the dispense tubes have a manual valve but the button turns on the pump and it will stay on as long as the button is pressed but it will go off in a few seconds once the button is released. The RODI unit is on the wall to the right of the workbench but is not in the photos.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
