Search results

Not sure about those working at 12v but make sure the Kraken output for Wave Engine is active in low power mode. Also I created a low power schedule and made it active during low power mode and set the rest of the schedules for my flow pumps to inactive in low power mode.

Yes like John says both need to be powered and also you will need a command bus cable and a couple of terminators to form a collective.

you cannot directly do it from the feeder output but you can create a virtual output for an output type that uses an external schedule. Then setup that schedule to run every other day. A light schedule you may be able to do that with. Then set the depends on on the wifi feeder to the virtual...

In the battery mode the force ports will only output 12v instead of 24v and that is only if you have them set to active in low power mode. Some pumps will not run at 12v and need 24v to run and others will as long as they are run at a lower speed during low power mode. I have a Sicce SDC 3.0...

Yes either the sensor has to go wet or you would have to use the override to turn it off and back to auto. Unless you are at the tank and can stop it another way I would not override it to on and then auto since if there is a communications issue once it is on you would not be able to get it...

Does the backup sensor go wet also or just the triple level overfull. There is very little difference in the wet level sensor and the overfull on the triple level sensor. The compartment may be small enough that the delay between the wet signal and turning the pump off is enough to trigger the...

If the wifi icon is red on the Sole then you can reboot it using device properties in the right menu. Once that icon is green you can do a upload changes from the right menu to fix the configuration mismatch. The Sole probably did not download the settings change and that caused the...

Sorry posted in the wrong feed.

There s a learning curve to any of the controllers. It is easier for someone that has not had a controller than someone that has quit a bit of experience with another controller since things are done differently in the different controllers. You can use a combiner output type setup with multiple...

I used to use a few outputs to do my DI refill before CoralVue added the RODI output. I discus it on my build thread on Reef Central. Since the two inputs for low and high level were input to output and those outputs were then used as inputs in other outputs. The post has a lot of info. You...

I have never heard of any of those brands. I have been using the Milwaukee pH probes lately. I have used Pinpoint also. I have the Milwaukee all glass one in my iV and I am happy with it using it there.

Have you tried setting it to external schedule and then setting up a schedule in schedules in the left menu and see if that acts any different? Also if you use a wifi outlet for a heater make sure there is a thermostat you can set on your heater as a backup off. If there is a communications...

On the one that is not connecting to the internet make sure that the device with the app installed is also on the same wifi channel you want the wifi feeder on. That should be the same one as controllers are on. Also make sure the wifi feeder is near the router while pairing it. Leave it powered...

You cannot use it in more than one output so you will have to delete it from the original output first. Your output may not be viewable on your page. Click and hold one of the output tiles for a second and release. Now all outputs should be there and have check boxes. Make sure the ones you want...

I used to control my RODI unit before they came out with the RODI output but it requires several outputs including outputs that would change the inputs to outputs so they could be used as inputs in a Combiner output type. i have the information in my build thread on Reef Central Here is a link...

There is a cable kit you can buy so you can use an IceCap v3 battery backup between the Wave Engine power supply and the Wave Engine power port. Here is a link HYDROS IceCap Battery Backup Cable Kit

You can also use minimum off time and minimum on time in the advanced settings to keep it from cycling frequently. Minimum off time would require it to remain off that amount of time before it can come back on.

If you use the standard AWC output type the drain is done first and then the fill. That is a lot of water to remove from a 12 gallon tank before refilling it. Any filters or skimmers that affect the water level need to be left on during the water change since it uses the ATO sensor during the...

i was also showing my feeder settings in that screenshot. The main one that creates the feed mode that is triggered by my wifi feeder is the one named feed mode. You would then use it in the depends on settings on any output you want off and set the dependency mode to off if on since you want...

You can use a push button in a button box if you have a unused 0-10v input. You may be able to start it with a mode also. You would have to create the mode then trigger the output on using the mode. You might have to create a couple of virtual outputs to do it. I used something similar to start...