Getting this error since the firmware update: iV: Value Unknown, (sensor disconnected ?) (b0a732990988)

Users Who Are Viewing This Thread (Total: 0, Members: 0, Guests: 0)

Danny said:
Have you tried using the web app and doing a upload changes?
Click to expand...
I opened it up, there's no "upload changes" button. I had problems when I first updated inside the app, I had to re-setup all of the inputs, and I uploaded changes after that, all in the app, and it worked just fine...
 
DigitaLSD said:
I opened it up, there's no "upload changes" button. I had problems when I first updated inside the app, I had to re-setup all of the inputs, and I uploaded changes after that, all in the app, and it worked just fine...
Click to expand...
other than this constantly repeating error...
 
DigitaLSD said:
I opened it up, there's no "upload changes" button. I had problems when I first updated inside the app, I had to re-setup all of the inputs, and I uploaded changes after that, all in the app, and it worked just fine...
Click to expand...
Click on the right menu and it is in the menu.
 
Can you share a screenshot of your iV output? The message seems to indicate it isn't liking your pH or conductivity probe. I'm thinking pH probe is missing or misconfigured and each scheduled iV test ends in error. Only question is what is error? Unable to reach terminal pH or initial pH out of range. That'd be visible below the left dropdown, LOGS then selecting the iV output. Think its going to tell us you lost or misconfigured the pH probe.
 
Danny said:
Click on the right menu and it is in the menu.
Click to expand...
Did that at around 8:45pm last night, test ran at midnight and still got the error... It's run two more times since then, and the error has been present both times... It does seem to come AFTER the testing is complete...
 
DigitaLSD said:
Did that at around 8:45pm last night, test ran at midnight and still got the error... It's run two more times since then, and the error has been present both times... It does seem to come AFTER the testing is complete...
Click to expand...

Can you share a screenshot of the iV configuration and the log output?
 
@Danny I *think* I might have figured it out... I found it strange that my iV was named iV-2, and when I went to change it back to just iV, it said I couldn't because there was already an iV present... So I dug around and found an iV under inputs. I deleted it because it was set as a probe and I already have iV pH, iV Alkalinity, and iV Salinity setup as Inputs... so we'll see how it goes... I'll touch base after 1pm Central to see if the notification happened again...
 
DigitaLSD said:
@Danny I *think* I might have figured it out... I found it strange that my iV was named iV-2, and when I went to change it back to just iV, it said I couldn't because there was already an iV present... So I dug around and found an iV under inputs. I deleted it because it was set as a probe and I already have iV pH, iV Alkalinity, and iV Salinity setup as Inputs... so we'll see how it goes... I'll touch base after 1pm Central to see if the notification happened again...
Click to expand...
Yes, the new firmware will not allow a name to be used more than once and it will change one of them. Usually the safest one to change is the output if the other is a input. That will break anything that uses that output such as schedules, depends on settings and used as a input in a combiner output. I thought I had all of mine different and it found some when I updated but I think I found them all and got anything corrected to the new name.
 
Now that you've deleted the erroneous iV output you may also want to check your sanpled pH, alkalinity and salinity inputs to be sure they refwrence the correct iV output.
 
Danny said:
Yes, the new firmware will not allow a name to be used more than once and it will change one of them. Usually the safest one to change is the output if the other is a input. That will break anything that uses that output such as schedules, depends on settings and used as a input in a combiner output. I thought I had all of mine different and it found some when I updated but I think I found them all and got anything corrected to the new name.
Click to expand...
Well, it worked... No more error... However, I noticed a few other things, I went to go calibrate my pH probe and that was all jacked up in the system too... I'm 1/2 tempted to just shut everything down and restart it from scratch setting up all of the individual things again just so I can be certain I don't miss anything else...
 
DigitaLSD said:
Well, it worked... No more error... However, I noticed a few other things, I went to go calibrate my pH probe and that was all jacked up in the system too... I'm 1/2 tempted to just shut everything down and restart it from scratch setting up all of the individual things again just so I can be certain I don't miss anything else...
Click to expand...
That is odd I did not have any issue with pH calibration on my pH ports and one is used in the iV.
 
You must log in or register to reply here.
Back
Top