Search results

I have never had an issue with it reconnecting and I have 15 controllers in one of my collectives. I do have my own wifi router and do not use one supplied by my cable company. So if I have internet I can always check on the the controllers. I do also have a UPS for the router and cable modem...

I used a output that is triggered using the feeder output. I also set the minimum on time to 30 minutes. I called it Feed Mode and I use it to either turn off the output via the output's depends on or switch to the feed mode schedule using the schedules depends on. Set the feed mode schedule...

I don't see that you have an alert setup in that output. Are you sure you are not getting alerts for a previously setup output? If an alert is active and you delete the associated input or output you will continue to get the alerts since they are in the que and will remain there until you clear...

That supply may have other uses besides the Kraken that is not known to us at this time. Either one will work with the Kraken.

Setup an output that is dependent on the inputs being in the right state using the generic output. Set it to be on when it ok for the AWC to run. I have one I use for control of the AWC and one for the ATO like this. The first screenshot is the output for AWC control. My drain pumps to the...

I have not tried this but you have a schedule for the pump. If you could create a schedule that has a lower speed and use a output to select that schedule using the depends on in the schedule and use the return coming on as the input and set a maximum on time for that output and set run past max...

The communications between the controllers and power plugs are a Tuya protocol communications and is done locally and not through the cloud but my understanding is both need to be on the same access points for them to communicate correctly. When pairing make sure the device the app is installed...

The device and controller have to be on the same access point to be able to talk to each other. Also your wifi may block that type of communication since it is a business.

Yes, when you are setting up wifi devices your device you are using with the app on it has to be on the channel you want the wifi device on. In this case that would be the channel with to controller that will be controlling it.

They are not as precise as the X10 pumps would be but that is still close.

Are you sure they are just not connecting to wifi any longer. You can use the left menu and the + sign to setup the wifi info again. Just don't change the controller name. You will need to do this for any controllers that did not reconnect to the wifi.

Have you calibrated you pH probe. Those calibration numbers are not right, There should be a mv offset for pH 7 and a percentage on the pH 10 and pH calibration points. The percentage should be around 100%. Yours is showing 0% for both. The pH 4 calibration is needed when using the pH probe in...

What are you trying to schedule on certain days? The external schedule like for dosing will do that for certain days of the week.

you don't have to be logged into the controller. Use the + sign in upper right of left menu and the select the controller you want to change the wifi settings on. This is the same way you originally set them up but don't change the controller name.

For one you don't want to turn off anything that will affect the normal running water level since the AWC uses that water level. Also the AWC output does need to control you ATO pump since the water level sensor needs to be wet to start the AWC. and the fill pump will run till it is wet again...

Go to the settings for your iV test output and there is a setting for the output for both pH and salinity. There is an arrow that point at an angle up to the right of the probe port selection. this will take you to the settings for that input if you click on it. I assume you did calibrate those...

What does it read in the pH 10 solution. That is also part of the calibration. You have to calibrate both points.

You can try going in and putting in you wifi info like you did when setting up the controllers to begin with. Just don't change the name of the controller. See if the controller connects to wifi after that. If that works then do the same to any others having the issue.

It sounds like it is getting to the reagent dispense part and stopping there with an error. Have you tried clearing the error and the doing a manual pH and salinity test to see if it also errors on that test. the only reagent dispense on that is a short amount at the very beginning otherwise it...

The salinity showing 0 ppt does not seem right. There is two hidden inputs for the realtime reading for the p( and salinity inputs. It would be interesting to see what they are showing. I setup a page for all my testing and set the hidden tiles so they will be visible.I also setup so only the...